Board Size: 6-5/8" L x 4-1/2" W
Wizard - 3 Board is pre-assembled and tested.

Wizard-3 Manual

Wiz-3 Board Application

Note:
Regulated 9 Vdc @ 2 Amp and
Regulated 6 Vdc @ 2 Amp
power supplies recommended

Example Setup
Wizard-3 Manual / Overview

The Wizard 3 board will record and playback up to 4 separate tracks for up to 8 R/C type servos channels and 8 digital channels. The maximum recording time per track is 3 minutes for multiple track operation or 6 minutes for single track operation. The card incorporates features such as looping action with variable delay between loops, auto start-up on power up, a connection interface for a PIR, remote switch or pressure pad to initiate playback and the ability to daisy-chain several
cards together. The card may be connected to the optional Sound Board Pro to provide audio accompaniment to the tracks.

Recording tracks are built up in real time on a channel-by-channel basis no programming is required.

During recording all previously recorded channels are re-played to aid synchronization.

NOTE: Controller requires 2 Power Supplies(1-9VDC and 1-5 or 6VDC)
NOTE: Sound Board Pro required if sound option is used.

( 9 Vdc @ 2 Amp and 5-6 Vdc @ 2 Amp power supplies recommended )

Regulated Power Supplies ( 5-6 and 9 VDC ) and Servos, not included.

Super Animatronic Board

2- servos, 2- Relays, Digital Out, Sound Chip and Sound to Motion,
all on one controller board.


Enhanced Sound now with
4 minute sound chip on board

Board Size: 6"L x 4"W x 1"H

Controller has 7-bit Resolution.
Wizard - 5 Board is pre-assembled and tested.

Recommended 9 Vdc @ 2 Amp power supply

Wizard-5 Manual

Wizard - 5 Board Overview

Wizard - 5 Board Applications

Product Video

The Wizard - 5 Board will record and playback up to 5 minutes of action for up to 2 servos and 2 digital outputs (on-board relays). It also incorporates a 4-minute audio recording and playback sound chip with the ability to control one servo channel either from recorded moves or from an audio signal, direct or from on-board sound chip.
The card includes features such as looping action with variable delay between loops, auto start-up on power up and a connection interface for a PIR, remote switch or pressure pad to initiate playback.
Recording sessions are built up on a track-by-track basis- no complex programming is required and no computer is needed. During recording, all previously recorded tracks are re-played to aid synchronization.

Wizard - 5 Board Features
2- Digital channels- either 0/4V @ 10mA outputs or relay rated 30V @ 2A .
2- Servo channels ­ one channel may be automatically controlled from an audio signal either from the line input or from the on-board sound chip.
4 minute, high quality sound chip- digital recording selected from either from the line input (ie from a sound card and wav files) or from microphone input.
Potentiometer to adjust the servo position and the time delay between loops in loop-play.
Digital ON-OFF, NEXT, PLAY and RECORD buttons.
Record enable/disable jumper, EEprom protect jumper.
AUTO-PLAY and LOOP-PLAY switches.
Sync output for multi-board operation.
Programmable Recording time - 5 Minutes
Remote start option- for switches, sensors / PIRs, etc.
Maximum and minimum set points to the audio servo channel, and many more features.

Power supply, Servos, not included.
( 9 Volt dc @ 2 Amp power supply needed )

The Wizard - 8 board provides a single channel, user programmable 5 - minute digital output (relay) combined with a digital 4 - minute duration user record IC sound chip. The supplied 4 - minute ISD sound chip has great frequency response up to 3.4 KHz and a audio sample rate of 8.0 KHz. Audio can be re-recorded up to 100,000 times and can be stored up to 100 years.

One - Digital channel - either 0/4.5V @ 50mA output or on-board relay rated 30V @ 2A with wire terminal strip.
One - 4 minute quality digital IC sound chip.
Digital recording to Sound IC chip is through a direct line input (Computer sound card or output port, CD player or any sound source output).
Potentiometer to adjust the time delay between loops in playback of recorded sound and relay action ON and Off.
Digital ON - OFF and GO programming buttons, AUTO - PLAY, PLAY - RECORD and SOUND - RELAY switches. No computer is needed for programming.
Programmable Relay Recording time - 5 Minutes
Programmable Sound Recording time - 4 Minutes
Sync output for multi-board and link to other Wizard board operation
REMote start option - for interfacing to sensors, switches, remote relays, pressure pads, PIR sensors, etc.

Board operates from regulated 9 VDC @ 1.0 Amp power supply.
( Power supply, audio cable, remote audio amplifier and speakers not included.)

Ultimate Animatronic Board

6- Servos, 2- Relays, 4- minute Digital Out,
Sound Chip and Sound to Motion
(AutoTalk) control, all on one single controller board.

Click on image for larger view


Board Size:
7-3/8" L x 4-1/8" W x 1/2" H
Board is pre-assembled and tested.
Controller has 7-bit Resolution.

Wizard-11 Manual

NOTE:
The Wizard -11 requires
duo power supplies

9 VDC @ 1.0 Amp power supply .....
5 - 6 VDC @ 2.0 Amp power supply
(Servo Power)

Wizard -11 Controller
-vs-
Other Controllers

YouTube Videos of Animatronic
Characters using Wizard Boards

The Wizard - 11 Board will record and playback up to 6 minutes of action for up to 6 servos and 2 digital outputs (on-board relays). It also incorporates a 4-minute audio recording and playback sound chip with the ability to control one servo channel (AutoTalk) either from recorded moves or from an audio signal, direct or from on-board sound chip.
The card includes features such as looping action with variable delay between loops, auto start-up on power up and a connection interface for a PIR, remote switch or pressure pad to initiate playback.
Recording sessions are built up on a track-by-track basis- no complex programming is required and no computer is needed. During recording, all previously recorded tracks are re-played to aid synchronization.

Wizard - 11 Board Features
2- Digital channels- either 0/4V @ 10mA outputs or relay rated 30V @ 2A .
6- Servo channels ­ one channel may be automatically controlled from an audio signal either from the line input or from the on-board sound chip.
4 minute, high quality sound chip- digital recording selected from either from the line input (ie from a sound card and wav files) or from microphone input.
Potentiometer to adjust the servo position and the time delay between loops in loop-play.
Digital ON-OFF, NEXT, PLAY and RECORD buttons.
Record enable/disable jumper, EEprom protect jumper.
AUTO-PLAY and LOOP-PLAY switches.
Programmable Servos, Relay Recording time - 6 Minutes
Programmable Sound Recording time - 4 Minutes
Sync output for multi-board operation.
Remote start option- for switches, sensors / PIRs, etc.
Maximum and minimum set points to the audio servo

NOTE: The Wizard -11 requires twin power supplies.
On board electronics operate from regulated 9 VDC @ 1.0 Amp power supply
On board Relays and servo outputs operate from regulated 5 - 6 VDC @ 2.0 Amp power supply

( Power supplies, audio cable, remote audio amplifier servos not included.)

Small controller for single servo control with up to 4 minutes recording time, loop playback with variable time delay between loops, auto start-up and easy recording features. Several modules may be daisy chained together and controlled from one master module.

The Puppet Controller has an additional digital channel with a 1A @ 24 Vdc rated relay.
Record your servo channel first and then superimpose the digital channel whilst the servo is playing
The Puppet servo controller includes the following features:
- Single channel servo control
- Programmable Servo , Relay Recording time - 4 Minutes
- Full 180 degree rotation pulse train (for servos that can physically rotate 180 degrees)
- Looping play with adjustable time delay between loops Record edit function
- Synchronization pulse for multiple unit operation

( 5 Volt dc power supply and Servo not included )

.YouTube Videos of Animatronic
Characters using Puppet Controller

The Joystick Servo Controller is a dual channel servo controller capable of direct manual servo, relay control and with recording option of up to 13 minutes of servo and relay action, interfaced to a standard game joystick.

The board features loop playing with variable delay, synchronized playback, can be linked with several other boards for multiple servo applications, has servo movement limit setting and a single relay channel output.

Joystick forward and backwards controls servo one motions.
Joystick left and right controls servo two motions.
Thumb button = playback / recording
Trigger button = relay ON/Off control.

Pressing down and holding the Thumb button will activate the record option where joystick / servo motion is recorded to an on-board EEPROM for playback up to 13 minutes.
Playback motion can be later activate by pressing the finger button, anytime, even between manually servo control.
Board power is provided by plug-in wall unit, or optional mobile power supply and will operate both joysticks and servos.
Programmable Servo, Relay Recording time - 13 Minutes.

NOTE: Analog Joystick with DB-15 connector required. Will not work with new USB type joysticks.
( 9 Volt dc Power supply, Servos and Joystick not included )

Joystick Adapter Kits- Build Your Own Joystick Interface
( Joystick, power supply, servos, not included )

Puppet III Manual


Joystick Controller Document

Joystick Controller Applications

Product Video

Control board for manual operation of a single R/C type servo by remote switch, relay, wireless control or external automated controller signal pulse.
( Servo travel positions A to B or B to A, under switch signal operation ) When remote manual switch is activated servo arm will move to pre-programmed position (Min / Max) and return back to start pre-programmed position when remote switch is de-activated If remote switch is held active servo arm will stay in position until switch is de-activated.
Board also has on board Solid State Relay that can be manual operated On and Off with remote switch, external relay pulse, wireless controller.

Controller includes the following features:
- Single channel servo control.
- On-board connection for remote switch or relay.
- On-board Servo and Power Connection terminals.
- On-board travel adjustment for Servo Movement.
( A through B Min and Max positions )
- On board servo reversal switch
- Program buttons allow servo arm to be positioned with Start and Stop at any position between A and B travel and recorded to memory for playback.
- Servo Travel Position A to B - B to A control.
- Solid State Relay rated at 2amp switching (Com, NO.terminal contacts)
- 7-12 Vdc operation - Wall power or Mobile Battery
- Wire terminal blocks, Status LED's power connector, servo header pins.

(Power supply, hand switch button unit and servo not included )

Hand / Palm switch units can be custom designed to fit your unique needs. Call Blue Point Engineering for more information on a custom design.

This unique BPE exclusive controller uses a pre-programmed PIC Microprocessor to manually drive up to 4 model / hobby R/C servo motors simultaneously from 2 on board mini joysticks. On-board mini joysticks move the corresponding servo motor over their full travel range when moved. Controller also has on-board Solid State Relay controlled by micro push button switch. Small board design, entire board fits into the palm of your hand!

Solid State State Relay rated 12Vdc @ 1 Amp.
3- Pin Headers for quick servo connection.
Quick power connector on-board. Center positive 2.5mm jack.
On-board Mini Joysticks - 2 axis control per unit.
Each mini joystick controls 2 servos. ( 4 servos - 2 joysticks ).
Master power On and Off switch and status LED.
Relay On and Off status LED and quick connection wire terminal block with SS Relay - COM and NO connections.
Small Board size : 3-7/8" L x 2-1/2" W x 1" H.

Requires 5 Volt dc @ 2 Amp power supply.
Servo motors , Power supply - Not included.

Control Board will record and playback up to 5 minutes of servo motion for 2 standard 5 Vdc hobby R/C type servos and record and playback 2 digital Solid State Relay switched ON and OFF output.

The board incorporates many features such as looping playback servo motion with variable delay between loops. An on board connector for remote activation switching such as a PIR sensor, contact switch or mat pressure pad to initiate playback.

Recording sessions are built up on a channel by channel process - no complex programming is required. During recording, all previously recorded channels are re-played to aid synchronization the current channel being programmed. Programming is easily done, with a set of push button keys and control potentiometer built onto the board.
No host computer or other programming device is needed to operate the board,

Duo Power supplies, Servos, not included.
( 9 Volt dc @ 800mA power supply needed )
( 5 Volt dc @ 2 Amp power supply needed )

Specifications:
2- Digital channel- Solid State Relay output rated 2 Amp (On/Off Control).
2- Servo channels ­ Operate R/C servos
Potentiometer to adjust the servo positions.
Programmable Recording time - 5 Minutes
Potentiometer to adjust the time delay between loops in loop-play.
Programming Buttons RELAYS ON-OFF, SERVOS, RECORD buttons.
Record enable/disable jumper, EEprom protection switch
Remote start option- for switches, sensors / PIRs, etc
Many more features.

Board Size:
4-7/8" Long x 3" Wide x 1-3/8" High

Controller Requires Duo Power:
5 Vdc @ 1 Amp Power Supply and
9 Vdc @ 800 mA Power Supply ....

Board is pre-assembled and tested.

Controller Instructions

Controller Board will record 3-(12.5 minutes each routine) and playback the 3 different programmed servo routines to one standard hobby R/C type servo when activated. Manual operated on board Solid State digital relay has switched ON and OFF output. 3 - different servo control routines are pre-recorded into memory by the user. Programmed routines are then played back to servo by selecting 1-3 manual playback switch, or setting the board to looping or sequence function.
Board can be set to sequence function, where each servo routine is played back as channel 1 is activated. On board looping playback feature lets board run automatically. On board relay and servo routinesi can be activated by maual switch, remote relays or even by wireless hand held control.

Recording sessions are built up on a channel by channel process - no complex programming is required. Programming is easily done, with a set of switches and a control potentiometer built onto the board.
No host computer or other programming device is needed to operate the board.
Board is triggered by manual switches, remote relays or even by wireless hand held control.

Duo Power supplies, Servos, not included.
( 9 Volt dc @ 800mA power supply needed )
( 5 Volt dc @ 1 Amp power supply needed )

Specifications:
1- Manual operated Solid State Relay output rated 2 Amp (On/Off Control).
1- Servo channels ­ Operate R/C servo
3- Programming memory modules (12.5 minute record time each)
Potentiometer to adjust the servo positions.
Switch connection terminal blocks on board.
Many more features.

Control Board will record and playback up to 4 minutes of servo motion for one standard 5 Vdc hobby R/C type servos and sequence of on/off relay closures

You record a sequence of on/off relay closures and the independent movement of a R/C servo to on board EEprom memory. Programming is easily done, with a set of push button keys and control potentiometer built onto the board. Recorded program playback entered, can be started by pressing Play switch or connecting to a dry contact switch closure for remote triggering. Board features program loop Requires 7.5 - 24V DC for operation. ( not Included)

Relay outputs rated 10 Amp each
Programmable Recording time - 4 Minutes

Servo, Power supply, not included

Control Board will record and playback up to 6 minutes of servo motion for one standard R/C type servos and sequence of on/off action to one Solid State Relay.

You record a sequence of on/off relay action and the independent movement of a R/C servo to on board EEprom memory. Programming is easily done, with a set of push button keys and control potentiometer built onto the board. Recorded program playback, can be started by pressing Play switch or connecting to trigger input port for remote activation by switch or sensors. Board features program looping with variable delays, Trigger input and Sync output to connect to other control boards. Servo travel min and max limits can be programmed into controller
LED status lights aid in programming and operation. Board has On and Off power switch, EEprom lock out to protect recorded routine from being accidentally erased. On board servo connection header pin, and connection wire terminal blocks.

Requires 7.5 - 12V DC @ 900mA power supply for operation. ( not Included)
Solid State Relay is rated at 2 Amps
Programmable Recording time - 6 Minutes
Servo, Power supply, sensors not included

Board allows the control 3 solid state Relays and 6 Servo Motors. The user can program an On Time for each relay, min and max servo movement limits, up to six minutes of servo movement for each servo and a Loop Time. For the relays, the On Times can be different and can range from 0 seconds to 5 minutes. The Loop Time can be from 0 seconds to 5 minutes as well. The board can be triggered by applying a dry switch closure at the Trigger terminal or by pressing the Trigger pushbutton. An AutoStart switch is provided so that, if switched on, the board will immediately go to waiting for a trigger event to start the playback. The user enters all time settings via menu-driven LCD. The servo movement is programmed via the on-board potentiometer. The board requires 7.5V to 24VDC at 100 mA. Due to the large current required by the servos, a separate terminal is provided for supplying 5V from a separate power supply.

( Servo, Power supply, not included )

Programmable one channel Servo and Solid-State Relay Controller.
This setup consists of three boards.

Board 1- Master Programmer
Board 2- Playback / Memory Module
Board 3- Connection Module

Multiple Playback / Memory boards can be used by one Master Programmer module. Multiple playback / memory modules can be programmed from a single Master Programmer. The remote connection module makes set-up quick and easy.

Once the Playback / Memory module has been programmed the Master Programmer can be removed and a remote connection board attached.

Board Size:
4-3/4" L x 4-1/4" x 1" H

This unique board will allow the control of 4 servos manually via remote 10K potentiometers or by Wizard -1 Board control. The input (pots or Wizard Board) is selected by on-board slide switch or dry contact closure to the Remote Input Selection terminal block. When switched to (M)anual, the 4 servos are independently controlled by the remotely mounted pots. Minimum and maximum limits can be set for each servo but these limits are only in effect when the board is in (M)anual control. When in (W)izard mode, the Wizard Board will handle limits for the servos. There is an on-board SS relay that can either be activated by dry contact closure at the Remote Relay Trigger terminal block or by pressing the small pushbutton located next to the relay.

( Power supply, 10K potentiometers, Servos, Wizard -1 Board not included )

This unique controller board was designed to allow the use of 2 on-board joysticks to control 4 servo motors. The minimum and maximum limits of movement for each servo can be programmed and are stored in non-volatile memory.

There is also a SS relay that is activated by a toggle switch.
Relay rated at 2 Amps

The board has separate power entries for board power and servo power with the ability of using a remote switch to turn either on or off.


Board Requires 9 Volt dc @ 1 Amp power supply.
Board Requires 5 Volt dc @ 5 Amp power supply.
Relay Rated: 12 Vdc at 1 Amp

( Servo motors , Power supply - Not included )

Main Controller Board Size:
4-1/2" L x 4-1/28" x 1" H

Remote Potentiometer Board Size:
3-1/2" L x 1-3/8" x 1/2" H

Remote Switch Board Size:
4-3/4" L x 1-3/4" x 1/2" H

(9VDC) for the controller is required
(5VDC) for the servos is required

Application and Connection Setup Overview

This unique board set was designed to allow the use of either switches and/or potentiometers to manually remote control 4-servo motors and 1-Remote Solid State 2 Amp Relay. The switches or potentiometers are located on small remote boards that are connected to the main board via an 8 foot ribbon cable.
The minimum and maximum limits of movement for each servo can be programmed and are stored in non-volatile memory. There is also a Solid State relay that is activated by a toggle switch (also on the remote boards). The master control board has separate power entries for board power and servo power with the ability of using a remote switch to turn either on or off. Both remote switch and potentiometer boards have LED indicators that show the presence of board power and servo power.

Boards can be stacked to create an expanding servo control setup ( Two boards= 8 servo control, Three boards = 12 servo control, Four boards stacked = 16, ect ).
Control Boards can also be stacked to have one master board operated by switches another master board operated by potentiometers stacked together as one set. This unique design allows for easy development of a WALDO or puppeteer type interface setup.
Master control board requires Switch or Potentiometer board.
Separate power (9VDC) for the controller and a separate power (5VDC) for the servos is required

(Power Supplies, Potentiometer Board, Remote Switch Board, Servos not included )

This unique 4 channel servo and 1 channel solid state relay board was designed to allow the use of a remote joysticks in manual or in user program mode to control 4 servo motors and 1- solid state relay.

The joysticks are located on a small remote board connected to the main board via an 6 foot ribbon cable. The minimum and maximum limits of movement travel for each servo can be programmed and are stored in non-volatile memory.

There is also a Solid State relay that is activated by a toggle switch (also on the remote board). The board has separate power entries for board power and servo power with the ability of using a remote switch to turn either on or off. Both remote boards have LED indicators that show the presence of board power and servo power.

The user has the ability to record and playback up to 10.5 minutes of servo and relay activity. User can switch between manual and recorded playback with on board pushbutton switches. When user is in playback mode, and needs to manual control servos, a simple press of the red stop button , halts the playback routine and instantly allow control of the servos / relay by manual method. Programming servo / relay motion is set by on board selection switch and the activation of the red record/ stop button switch during real time programming.

Board Requires 9 Volt dc @ 1 Amp power supply.
Board Requires 5 Volt dc @ 5 Amp power supply.

( Servo motors , Power supply - Not included )