Super Animatronic Board

2- servos, 2- Relays, Digital Out, Sound Chip and Sound to Motion,
all on one controller board.


Enhanced Sound now with
4 minute sound chip on board

Board Size: 6"L x 4"W x 1"H

Controller has 7-bit Resolution.
Wizard - 5 Board is pre-assembled and tested.

Recommended 9 Vdc @ 2 Amp power supply

Wizard-5 Manual

Product Video

The Wizard - 5 Board will record and playback up to 5 minutes of action for up to 2 servos and 2 digital outputs (on-board relays). It also incorporates a 4-minute audio recording and playback sound chip with the ability to control one servo channel either from recorded moves or from an audio signal, direct or from on-board sound chip.
The card includes features such as looping action with variable delay between loops, auto start-up on power up and a connection interface for a PIR, remote switch or pressure pad to initiate playback.
Recording sessions are built up on a track-by-track basis- no complex programming is required and no computer is needed. During recording, all previously recorded tracks are re-played to aid synchronization.

Wizard - 5 Board Features
2- Digital channels- either 0/4V @ 10mA outputs or relay rated 30V @ 2A .
2- Servo channels ­ one channel may be automatically controlled from an audio signal either from the line input or from the on-board sound chip.
4 minute, high quality sound chip- digital recording selected from either from the line input (ie from a sound card and wav files) or from microphone input.
Potentiometer to adjust the servo position and the time delay between loops in loop-play.
Digital ON-OFF, NEXT, PLAY and RECORD buttons.
Record enable/disable jumper, EEprom protect jumper.
AUTO-PLAY and LOOP-PLAY switches.
Sync output for multi-board operation.
Programmable Recording time - 5 Minutes
Remote start option- for switches, sensors / PIRs, etc.
Maximum and minimum set points to the audio servo channel, and many more features.

Power supply, Servos, not included.
( 9 Volt dc @ 2 Amp power supply needed )

Ultimate Animatronic Board

6- Servos, 2- Relays, 4- minute Digital Out,
Sound Chip and Sound to Motion
(AutoTalk) control, all on one single controller board.

Click on image for larger view


Board Size:
7-3/8" L x 4-1/8" W x 1/2" H
Board is pre-assembled and tested.
Controller has 7-bit Resolution.

Wizard-11 Manual

NOTE:
The Wizard -11 requires
duo power supplies

9 VDC @ 1.0 Amp power supply .....
5 - 6 VDC @ 2.0 Amp power supply
(Servo Power)

Wizard -11 Controller
-vs-
Other Controllers

YouTube Videos of Animatronic
Characters using Wizard Boards

The Wizard - 11 Board will record and playback up to 6 minutes of action for up to 6 servos and 2 digital outputs (on-board relays). It also incorporates a 4-minute audio recording and playback sound chip with the ability to control one servo channel (AutoTalk) either from recorded moves or from an audio signal, direct or from on-board sound chip.
The card includes features such as looping action with variable delay between loops, auto start-up on power up and a connection interface for a PIR, remote switch or pressure pad to initiate playback.
Recording sessions are built up on a track-by-track basis- no complex programming is required and no computer is needed. During recording, all previously recorded tracks are re-played to aid synchronization.

Wizard - 11 Board Features
2- Digital channels- either 0/4V @ 10mA outputs or relay rated 30V @ 2A .
6- Servo channels ­ one channel may be automatically controlled from an audio signal either from the line input or from the on-board sound chip.
4 minute, high quality sound chip- digital recording selected from either from the line input (ie from a sound card and wav files) or from microphone input.
Potentiometer to adjust the servo position and the time delay between loops in loop-play.
Digital ON-OFF, NEXT, PLAY and RECORD buttons.
Record enable/disable jumper, EEprom protect jumper.
AUTO-PLAY and LOOP-PLAY switches.
Programmable Servos, Relay Recording time - 6 Minutes
Programmable Sound Recording time - 4 Minutes
Sync output for multi-board operation.
Remote start option- for switches, sensors / PIRs, etc.
Maximum and minimum set points to the audio servo

NOTE: The Wizard -11 requires duo power supplies.
On board electronics operate from regulated 9 VDC @ 1.0 Amp power supply
On board Relays and servo outputs operate from regulated 5 - 6 VDC @ 2.0 Amp power supply

( Power supplies, audio cable, remote audio amplifier servos not included.)

The ANIMATE BOARD is a 9 Volt dc powered full feature Sound, Motion and Switched ON / OFF output control interface board.

The controller has on-board sound recording and playback in to a 20 second sound chip with microphone and speaker output and up to 40 seconds of recorded and playback motion saved to a EEPROM for 4 standard +5 Vdc servos and control of 4 digital switched ON and OFF outputs at + 4.5 Vdc (100 mA) per channel action.

The Animate board incorporates many features such as looping playback servo motion with variable delay between loops. An auto start-up on power option and on board connector for remote activation switching such as a PIR sensor, contact switch or mat pressure pad to initiate servo playback and on- board sound output.

Recording sessions are built up on a channel by channel process - no complex programming is required.
During recording, all previously recorded channels are re-played to aid synchronization the current channel being programmed.Programming is easily done, with a set of push button keys and control potentiometer built onto the board.Speaker connection terminal allow the addition of an 8-16 ohm speaker which can be driven directly from the Animate board .Motion, Sound and Switched ON / OFF outputs are all controlled from a single board.Connection pins on-board for servos, output hookups.

Programmable Servo Recording time - 40 Seconds
Programmable Sound Recording time - 20 Seconds
( 9 Volt dc - 2 Amp Power Supply, Servos and Speaker not included ).......